Cartridges GTX 22 - Vaporesso | Pack x2

3,5ml DTL Multifunctional RDL MTL Bottom Airflow Adjustable

You have the GTX Go 40 pod from Vaporesso? Then why not buy the replacement cartridge GTX 22 of the same brand? This will make it easier for you to change your e-liquid, in a flash without having to worry about emptying and refilling your tank.

The magnetic cartridge PCTG allows you to add up to 3.5 ml of e-liquid. The filling is done from the top by unscrewing the top cap. The SSS anti-leak system is very practical

With the pod Go 40 you enjoy an air draw DL, RDL or tight MTL

Compatible with GTX Vaporesso resistors.

Cartridges sold in packs of 2

3,5ml DTL Multifunctional RDL MTL Bottom Airflow Adjustable Top Filling

Vaporesso GTX 22 replacement cartridges

The replacement cartridge GTX 22 of Vaporesso is compatible with the pod GTX Go 40 of the same brand. It will be perfect if you want to switch e-liquid, and therefore flavor, easily and quickly. But also, in case the tank is worn. Be aware, however, that the cartridge is made of PCTG for more strength.

The GTX 22 Vaporesso replacement cartridge of 3.5 ml

The GTX go 40 pod is perfect for a DL, RDL or MTL draw depending on the coil used. The 3.5 ml PCTG 22 cartridge is connected to the battery via a magnet. Its technology SSS anti-leak is very appreciable to not find yourself with e-liquid on your fingers.

width=500

The cartridge is compatible with resistances GTX Vaporesso

- Resistance GTX 0.3 ohm (mesh): air draft DL - to use between 32 and 45W - ratio 50PG/50VG or 30PG/70VG - compatible with low nicotine levels (from 0 to 6 mg / ml)

- GTX resistor 0.6 ohm (mesh): air draft RDL for a balance between flavors and steam - to use between 20 and 30W - ratio 50PG/50VG or 30PG/70VG or 40PG/60VG - compatible nicotine rate of 0 to 9 mg / ml

- GTX resistor 0.8 ohm (mesh): RDL draw - to be used between 12 and 16W - ratio 50PG/50VG - compatible nicotine rate from 0 to 18 mg/ml

- GTX 1.2 ohm (mesh): MTL tight draw - to be used between 7 and 11W - ratio 50PG/50VG or 70PG/30PG or 60PG/40VG - compatible with nicotine salts and high nicotine levels (from 0 to 18 mg/ml)

The mesh technology ensures a beautiful vapor production and exceptional flavors. The adjustable airflow ring allows you to adjust the airflow according to your preferences. So you can switch from an airy draw to a tighter draw and vice versa.

width=500

How to use the GTX Go 40 Vaporesso cartridge?

The filling is done from the top(top-filling) simply by unscrewing the top cap with integrated drip tip. To replace the resistance, first remove the cartridge from the pod and then the damaged resistance. Prime a new coil and insert it before filling the tank, repositioning the cartridge and waiting 10 minutes to vaper.

width=500

Capacity (ml)
3,5ml
Type of inhalation
DTL, Multifunctional, RDL, MTL
Airflow
Bottom Airflow, Adjustable
Fill type
Top Filling
Compatible coils
GTX V2 coils
Country of manufacture
made in China

Complementary products

CHF7.90
In stock
Tax included

Free delivery from 29,90CHF purchase
If you don't smoke, don't vape

close

Wishlist