Pod Feelin 2 Cartridges - Nevoks | x2 Pack

3ml MTL RDL Bottom Airflow Pack of 2 units

Designed to accompany the Feelin 2 pod, manufacturer Nevoks offers us these cartridges also called Feelin 2 like this, it's hard to go wrong, but you're right to always be on your guard. This pack of two cartridges means you'll always have a spare tank in case of breakage or loss, because it's never a good idea to get into the mosh pit e-cig in hand. What's more, it allows you to juggle flavours with the ease of the vape maestro that you are.

The Feelin 2 cartridges feature a 3 ml PCTG tank that fills up from the side. You'll find the famous signature drip tip of the Feelin range, a duckbill-style tip with a soft touch coating for ultra-comfortable vaping.

The Feelin 2 cartridge is compatible with Nevoks' SPL 10 coils, whose mesh resistive will give you excellent flavours and great vapour production.

Sold in packs of two without coils.

3ml MTL RDL Bottom Airflow Side Filling Pack of 2 units

Product Description

Nevoks Feelin 2 replacement cartridges

The pack of two Feelin 2 cartridges offers the chance to quickly change e-liquid or replace a used tank in an instant. Nevoks offers here a quality PCTG cartridge, equipped with a 3 ml tank and a soft touch coated drip tip with a duckbill design, guaranteeing the most pleasant vape experience.

With which gear to use the Feelin 2 cartridge from Nevoks?

These Feelin 2 cartridges have been designed for the pod Feelin 2 from Nevoks. Find all the equipment compatible with these cartridges in the “complementary products” list.

What coils for my Feelin 2 cartridges?

To make your cartridges functional, they require the installation of Nevoks' SPL 10 coils (coils not included). Once inserted in your cartridge, they will offer a vape experience rich in flavour and more than satisfactory vapour production. Various models are available for an excellent MTL or RDL vape.

SPL 10 1.0 ohm (Mesh): MTL draw - to be used between 10W and 13W - PG/VG ratio from 70/30 to 50/50 - Nicotine rate up to 20 mg/ml (CBD e-liquid compatible).
SPL 10 0.8 ohm (Mesh) : MTL draw - to be used between 15W and 18W - PG/VG ratio from 60/40 to 50/50 - Nicotine rate up to 20 mg/ml.
SPL 10 0.6 ohm (Mesh): RDL draw - to be used between 18W and 25W - PG/VG ratio from 50/50 to 40/60 - Nicotine rate up to 12 mg/ml.
SPL 10 0.4 ohm (Mesh): RDL draw - to be used between 25W and 35W - PG/VG ratio from 50/50 to 30/70 - Nicotine rate up to 6 mg/ml.

Caution: Feelin 2 cartridges, or rather the Feelin 2 pod is not compatible with 0.3 ohm SPL 10 coils.

Filling the Feelin 2 cartridge:

Remove the cartridge from the battery (magnetic system).
Open the silicone tab, fill and then close again.
Put back the cartridge on the battery.

Replace the SPL 10 resistor:

Remove the cartridge from the battery (magnet system).
Remove the used coil by pulling on it.
Insert the coil under the cartridge with a simple press.
Put back the cartridge on the battery.
Caution: If the coil is new, prime it well by letting it soak in e-liquid for about ten minutes before vaping.

Beware, you need to change your coil approximately every 2 weeks depending on your usage. Remember to replace your coil when you change flavour or feel a burnt taste.

Technical characteristics